Use the Flipper Door Compariosn Chart
Which system is best for my application?
There are quite a few options to sort through. Consider size and weight of the doors. The different systems we carry will list the weight they can handle and in some cases specify height parameters. Consider your door design also. Some systems have options for both inset or overlay doors. Accurrides 1234 system also has an option for a thick inset door.
What length slide do I need to choose?
Two factors come in to play- the depth of the cabinet and the width of the door. You need to make sure that youll have enough depth in the cabinet to fit the slide you select. Obviously, you cant fit a 24" long slide into a 20" space. There will be a strip of either wood or metal that goes from slide to slide that the hinges will attach to. This strip takes up some space, so the travel distance (this is the amount of the door that will disappear when moved back into the cabinet) will be less than the length of the slide. As an example, if you had a 18" wide door and a 18" long slide, then only 14 to 15" hinge of the door will go back into the cabinet. If you used a 22" long slide with a 18" wide door, then all of the door would disappear into the cabinet.
What is meant by inset door and overlay door?
In inset door sits inside the face of the cabinet with the face of the door being flush with the face of the cabinet. On a flipper door system an overlay door will sit in front of the cabinet, with the hinge side of the door overlaying or covering up the front of the cabinet.
A cabinet is in essence a box. A face frame is a narrow piece of wood, usually about 2" wide that is attached to the front of this box, framing the opening where the doors go. Most flipper door systems are installed on cabinets without a face frame (this is called frameless construction). The Accuride 1234 system has one hinge option for an overlay door on a face frame. For all other designs you will need a cabinet without a face frame.
What is meant by travel distance?
This basically means the amount of door that will go back into the cabinet. If we have a 24" long slide with a travel distance equaling slide length minus 4-1/2", then the travel distance is 19-1/2". This means 19-1/2" of door will slide back into the cabinet when open.
Do I need to have the travel distance of the slide equal the width of my door?
No, in fact in most cases you wont want to as you may have handles or knobs on the door. If you have a few inches sticking out when the door is opened, then the handles or knobs wont smash into the cabinet. In a case where you want the door to retract all the way when open, then you need to explore the use of a recessed pull of some sort into your design.
What if I have a taller door than the system recommends?
Consider splitting the door into an upper and a lower door if possible. Or you might space the hinges in from the top and bottom of the door beyond the normal installation. If you decide to try this you will need to do more measuring and layout than the instructions will detail. Also, be sure not to exceed the per door weight rating recommend for the system.
Are these difficult to install?
They can be complicated. Some systems are easier to install. Accurides 1234 system is the easiest system to install and is recommended for the beginner as well as the experienced. You will find that installing a system into a new cabinet is easier than trying to retro-fit to an existing cabinet as you wont have to worry about possibly re-fitting the doors or having to make replacement doors.
Can these types of systems be installed in a horizontal application also?
Most systems are intended only for vertical applications. The MEDIUM DUTY system is the one recommended if you have a design that incorporates a horizontal door.
When a door gets larger it has a tendency to tip forward as you have the door open and are about to slide it back into the cabinet. This tendency is called racking. Some systems such as the Accuride heavy duty flipper door system have features designed to counter this tendency to rack. The Accuride heavy duty flipper door system uses a cable strung behind the follower strip to achieve this. This is more of a design consideration for larger doors than smaller doors.
What is a follower strip or carrier strip?
These terms are used interchangeably. These terms refer to the piece that goes from one slide to the other that the hinges are attached to. It some cases it is a wood piece that you make. It some cases it will be metal.
What if I have a door thicker than 3/4 inch?
Most systems are designed for doors 3/4" thick. If you try to use a thicker door with these it will not work as the face of the door will sit out too far and/or it will scrape on the slides as the door is slide back into the cabinet. The Accuride 1 2 3 4 system has a hinge option for inset doors up to 1-1/4" thick. This is the only option available for thicker doors and it is for inset doors only.
Can the slides be cut down to a shorter length?
No, they cannot be cut. Most systems use a ball bearing slide and you may lose the bearings if the ends are cut. Any alterations such as this will void all warranties.
How much space will the hardware take up?
Depending on which system you choose, they will take from1-3/4" to 2-1/4" of space per side for hardware and door combined.
How should I size my door if I want to start building before I get the hardware?
To be on the safe side, please dont make the doors until you have the hardware in hand. Youll want to take some time reading through the instructions that come with the system you choose to ensure that you design and layout the door properly.
Rockler Gift Certificate |
| ||||||||||
We do not sell to and/or ship to the state of New York. Sorry, the new state "vendor" tax code is harsh and costly! | ||||||||||
Training |
Woodworking
Wholesale Wood / Pen Supplies Rockler | Pen Making
Home Automation & Surveillance
|
|||||||||
1-Chronicles 4:10 |